Step by step on how to install the Blitz Sliders on a Lexus GX460 (10-23). Please read all steps carefully before starting the install.
Installation Video: https://www.youtube.com/watch?v=6ZbQVIfVyPc
Questions or Support:
Phone: 269-353-1184
Email: info@victory4x4.com
Check that you have all of the parts shown before starting.
Check that you have all of the hardware shown before starting. Hardware packs: 046-0025 and 046-0041 (every bolt, nut and washer is listed in the bill of materials picture).
Remove the two screws in the front wheel well and the one in the rear wheel well (10mm socket or Phillips). Then remove the Phillips screw behind each door.
Video timestamp: 0:30
Pry up the step cover plate with a flat blade screwdriver or clip tool, working front to back. Then remove the three 10mm bolts underneath.
Video timestamp: 1:40
Unplug the factory wiring harness for the step lights underneath, then remove the six bolts holding the step to the vehicle.
Video timestamp: 2:45
Open the doors and pull the lower plastic trim straight out to release the factory clips.
Video timestamp: 3:18
Remove the three metal clips and the plastic clips across the center. Pry off the tab on each end (held with double sided tape) and slide the center out.
Video timestamp: 3:50
Measure down 3-1/4 in. from the top edge at the front (lines up with the body seam) and 2 in. at the rear. Tape a straight line front to back.
Video timestamp: 5:40
Cut along the tape with a cutoff wheel (an air saw also works). Discard the bottom section.
Video timestamp: 6:40
Snap the trimmed piece back in place, clean up the cut with a flap disc if needed, and reinstall the wheel well and door screws.
Video timestamp: 7:20
Disconnect the two light connectors on the factory step and remove the harness clips. The harness is reused to wire the rock lights.
Video timestamp: 8:05
Each slider is marked with a forward-facing arrow. Install the legs with arrows forward and the larger bracket at the rear using the button head bolts and serrated nuts. Push the legs as far forward as they go.
Video timestamp: 8:55
Install the LED lights using the provided button head bolts, washers, and lock nuts. Make sure the lights are centered in the hole and tighten them down using a 3mm allen and a 5/16” socket or wrench.
Video timestamp: 9:45
Route the factory harness behind the legs. Cut off the factory connector, shorten the light leads, and connect red to red and the black wire to the white/black stripe wire with the heat shrink butt connectors.
Video timestamp: 10:50
With KDSS, remove the two line brackets and the parking brake cable bolt. Remove the KDSS skid and the plastic cap at the front, and the three fuel tank skid bolts so the skid drops down.
Video timestamp: 13:10
Slide the rear bracket behind the KDSS clip and above the fuel tank skid. Bend the skid center tab flat. Install five bolts in the frame, the three skid bolts, and reattach the parking brake cable (top hole bolt, bottom hole tab).
Video timestamp: 14:40
Install the front bracket behind the KDSS lines with six bolts: two in the bottom crossmember and four in the side of the frame. Tighten once all are started.
Video timestamp: 15:45
Center the slider on the wheel wells, then tighten the button head bolts. Some 3/4 in. nuts can be reached through the jack holes. Connect the wiring.
Video timestamp: 16:25
Remove the parking brake cable bracket at the rear and the frame clips so the bracket sits flush.
Video timestamp: 16:45
Push the front leg up and tighten the four side bolts. Center punch the two lower holes, drill 5/16 in. pilot holes, touch up bare metal, and install the 3/8 in. self-tapping bolts. Do not over-tighten.
Video timestamp: 17:45
15 Min - SOPs, Guide
6 Min - Guide
2 Min - Guides and Video
10 Min - Guides and Video
Suggest an improvement, or report a bug, direct from the app/platform.
Connect GembaDocs with external systems
